This allows querying and setting the route preference. It's usually set from
the IPv6 Neighbor Discovery Router Advertisement messages.
Introduced in "ipv6: expose RFC4191 route preference via rtnetlink", enqueued
for Linux 4.1.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
- Pull in the uapi mpls.h
- Update rtnetlink.h to include the mpls rtnetlink notification multicast group.
- Define AF_MPLS in utils.h if it is not defined from elsewhere
as is done with AF_DECnet
The address syntax for multiple mpls labels is a complete invention.
When I looked there seemed to be no wide spread convention for talking
about an mpls label stack in text for. Sometimes people did:
"{ Label1, Label2, Label3 }", sometimes people would do:
"[ label3, label2, label1 ]", and most of the time label
stacks were not explicitly shown at all.
The syntax I wound up using, so it would not have spaces and so it
would visually distinct from other kinds of addresses is.
label1/label2/label3 Where label1 is the label at the top of the label
stack and label3 is the label at the bottom on the label stack.
When there is a single label this matches what seems to be convention
with other tools. Just print out the numeric value of the mpls label.
The netlink protocol for labels uses the on the wire format for a
label stack. The ttl and traffic class are expected to be 0. Using
the on the wire format is common and what happens with other address
types. BGP when passing label stacks also uses this technique with the
exception that the ttl byte is not included making each label in a BGP
label stack 3 bytes instead of 4.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
This attribute is like RTA_DST except it specifies the destination
address to place on a packet when it leaves the host. For ip based
protocols this is destination NAT and not a common part of forwarding.
For protocols like MPLS label swapping is something that typically
happens on every hop.
There is likely to be a RTA_NEWSRC at some point so RTA_NEWDST
is printed as "as to" and can be specified either as "as to"
or just "as"
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Add support for the RTA_VIA attribute that specifies an address family
as well as an address for the next hop gateway.
To make it easy to pass this reorder inet_prefix so that it's tail
is a proper RTA_VIA attribute.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Add the functions family_name and read_family to convert an address
family to a string and to convernt a string to an address family.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
For some address families (like AF_PACKET) it is helpful to have the
length when prenting the address.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
This work adds the tc frontend for kernel commit e2e9b6541dd4 ("cls_bpf:
add initial eBPF support for programmable classifiers").
A C-like classifier program (f.e. see e2e9b6541dd4) is being compiled via
LLVM's eBPF backend into an ELF file, that is then being passed to tc. tc
then loads, if any, eBPF maps and eBPF opcodes (with fixed-up eBPF map file
descriptors) out of its dedicated sections, and via bpf(2) into the kernel
and then the resulting fd via netlink down to cls_bpf. cls_bpf allows for
annotations, currently, I've used the file name for that, so that the user
can easily identify his filter when dumping configurations back.
Example usage:
clang -O2 -emit-llvm -c cls.c -o - | llc -march=bpf -filetype=obj -o cls.o
tc filter add dev em1 parent 1: bpf run object-file cls.o classid x:y
tc filter show dev em1 [...]
filter parent 1: protocol all pref 49152 bpf handle 0x1 flowid x:y cls.o
I placed the parser bits derived from Alexei's kernel sample, into tc_bpf.c
as my next step is to also add the same support for BPF action, so we can
have a fully fledged eBPF classifier and action in tc.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Joining multicast group on ethernet level via "ip maddr" command would
not work if we have an Ethernet switch that does igmp snooping since
the switch would not replicate multicast packets on ports that did not
have IGMP reports for the multicast addresses.
Linux vxlan interfaces created via "ip link add vxlan" have the group option
that enables then to do the required join.
By extending ip address command with option "autojoin" we can get similar
functionality for openvswitch vxlan interfaces as well as other tunneling
mechanisms that need to receive multicast traffic.
example:
ip address add 224.1.1.10/24 dev eth5 autojoin
ip address del 224.1.1.10/24 dev eth5
On ip route print dump, label externally offloaded routes with "external".
Offloaded routes are flagged with RTNH_F_EXTERNAL, a recent additon to
net-next. For example:
$ ip route
default via 192.168.0.2 dev eth0
11.0.0.0/30 dev swp1 proto kernel scope link src 11.0.0.2 external
11.0.0.4/30 via 11.0.0.1 dev swp1 proto zebra metric 20 external
11.0.0.8/30 dev swp2 proto kernel scope link src 11.0.0.10 external
11.0.0.12/30 via 11.0.0.9 dev swp2 proto zebra metric 20 external
12.0.0.2 proto zebra metric 30 external
nexthop via 11.0.0.1 dev swp1 weight 1
nexthop via 11.0.0.9 dev swp2 weight 1
12.0.0.3 via 11.0.0.1 dev swp1 proto zebra metric 20 external
12.0.0.4 via 11.0.0.9 dev swp2 proto zebra metric 20 external
192.168.0.0/24 dev eth0 proto kernel scope link src 192.168.0.15
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Reviewed-by: Jiri Pirko <jiri@resnulli.us>
Next argument after the tc opcode/verdict is optional, using NEXT_ARG()
requires to have another argument after that one otherwise tc will bail
out. Therefore, we need to advance to the next argument manually as done
elsewhere.
Fixes: 86ab59a666 ("tc: add support for BPF based actions")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jiri Pirko <jiri@resnulli.us>
commit f3a2ddc124 ("lib utils: Use helpers to get AF bit/byte len")
used a wrong family or family of zero in the default case
during af_bit_len calculation causing ip route commands to
fail with below error
Error: an inet prefix is expected rather than "10.0.2.14/24".
Reported-by: Sven-Haegar Koch <haegar@sdinet.de>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Don't insert newline in -o (oneline) mode; print mark as hex.
Oneline mode is supposed to force all output to be on oneline and
machine-parsable, but this isn't the case for "ip xfrm" as shown:
% ip -o xfrm monitor
...
src 0.0.0.0/0 dst 0.0.0.0/0 \ dir out priority 2051 ptype main \ mark -1879048191/0xffffffff
tmpl src 203.0.130.10 dst 198.51.130.30\ proto esp reqid 16384 mode tunnel\
...
as that's 2 lines, not one. Also, the "mark" is shown in signed
decimal, but the mask is in hex. This is confusing: let's use
hex for both.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
This patch replaces exits with returns in several
iproute2 commands. This fixes `ip -batch -force`
to not exit but continue on errors.
$cat c.txt
route del 1.2.3.0/24 dev eth0
route del 1.2.4.0/24 dev eth0
route del 1.2.5.0/24 dev eth0
route add 1.2.3.0/24 dev eth0
$ip -force -batch c.txt
RTNETLINK answers: No such process
Command failed c.txt:2
RTNETLINK answers: No such process
Command failed c.txt:3
Reported-by: Sven-Haegar Koch <haegar@sdinet.de>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
While looking at the manpage, I noticed a reference to 'embedded' that was
added by this commit:
commit d611682a8c
Author: John Fastabend <john.r.fastabend@intel.com>
Date: Thu Sep 13 23:50:36 2012 -0700
iproute2: bridge: finish removing replace option in man pages
I no longer see any reference to the 'embedded' option in any c- or h-files, so
it seems worthwhile to remove.
Signed-off-by: Andy Gospodarek <gospo@cumulusnetworks.com>
CC: John Fastabend <john.r.fastabend@intel.com>
Where used in the ip tool, the 'show' option always has the synonyms
'list' and 'lst', except for ip-token and ip-addrlabel, which are missing
'lst'. Add this as a synonym for these commands.
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Observed on the Linux 3.18:
# ip netns
RTNETLINK answers: Operation not supported
net0
CC: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Fixes: d182ee1307 ("ipnetns: allow to get and set netns ids")
Signed-off-by: Vadim Kochan <vadim4j@gmail.com>
Added some clarification why 'ip link set netns' can not
change network namespace for some kind of devices.
Signed-off-by: Vadim Kochan <vadim4j@gmail.com>
Left-overs when copying this over from cls_bpf. ;) Lets remove them.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Jiri Pirko <jiri@resnulli.us>
This patch adds support to specify 'master' keyword,
to target a bridge link command explicitly to the software
bridge driver.
Adds self/master keywords to usage and man page
v2:
fix usage to say (self and master) and not (self or master)
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
The existing behaviour forces one to memorize the integer constants for
STP port states.
# bridge link set dev dummy0 state 3
This patch makes it possible to use the lowercased port state name.
# bridge link set dev dummy0 state forwarding
Invalid non-integer inputs now cause exit with status -1.
Signed-off-by: Alex Pilon <alp@alexpilon.ca>
When this attribute is set, it means that the i/o part of the related netdevice
is in another netns.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
This new attribute is now advertised by the kernel for x-netns interfaces.
It's also possible to set it when an interface is created (and thus creating a
x-netns interface with one single message).
Example:
$ ip netns add foo
$ ip netns add bar
$ ip -n foo netns set bar 15
$ ip -n foo link add ipip1 link-netnsid 15 type ipip remote 10.16.0.121 local 10.16.0.249
$ ip -n foo link ls ipip1
3: ipip1@NONE: <POINTOPOINT,NOARP> mtu 1480 qdisc noop state DOWN mode DEFAULT group default
link/ipip 10.16.0.249 peer 10.16.0.121 link-netnsid 15
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
The kernel now provides ids for peer netns. This patch implements a new command
'set' to assign an id.
When netns are listed, if an id is assigned, it is now displayed.
Example:
$ ip netns add foo
$ ip netns set foo 1
$ ip netns
foo (id: 1)
init_net
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Lubomir Rintel
Eric W. Biederman
Daniel Borkmann
Stephen Hemminger
Madhu Challa
Scott Feldman
Vadim Kochan
Roopa Prabhu
philipp@redfish-solutions.com
Andy Gospodarek
Mark Einon
Eric Dumazet
Ebben Aries
Hagen Paul Pfeifer
Lennart Sorensen
Nicolas Dichtel
Alex Pilon
Bryton Lee