This allows querying and setting the route preference. It's usually set from
the IPv6 Neighbor Discovery Router Advertisement messages.
Introduced in "ipv6: expose RFC4191 route preference via rtnetlink", enqueued
for Linux 4.1.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
- Pull in the uapi mpls.h
- Update rtnetlink.h to include the mpls rtnetlink notification multicast group.
- Define AF_MPLS in utils.h if it is not defined from elsewhere
as is done with AF_DECnet
The address syntax for multiple mpls labels is a complete invention.
When I looked there seemed to be no wide spread convention for talking
about an mpls label stack in text for. Sometimes people did:
"{ Label1, Label2, Label3 }", sometimes people would do:
"[ label3, label2, label1 ]", and most of the time label
stacks were not explicitly shown at all.
The syntax I wound up using, so it would not have spaces and so it
would visually distinct from other kinds of addresses is.
label1/label2/label3 Where label1 is the label at the top of the label
stack and label3 is the label at the bottom on the label stack.
When there is a single label this matches what seems to be convention
with other tools. Just print out the numeric value of the mpls label.
The netlink protocol for labels uses the on the wire format for a
label stack. The ttl and traffic class are expected to be 0. Using
the on the wire format is common and what happens with other address
types. BGP when passing label stacks also uses this technique with the
exception that the ttl byte is not included making each label in a BGP
label stack 3 bytes instead of 4.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
This attribute is like RTA_DST except it specifies the destination
address to place on a packet when it leaves the host. For ip based
protocols this is destination NAT and not a common part of forwarding.
For protocols like MPLS label swapping is something that typically
happens on every hop.
There is likely to be a RTA_NEWSRC at some point so RTA_NEWDST
is printed as "as to" and can be specified either as "as to"
or just "as"
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Add support for the RTA_VIA attribute that specifies an address family
as well as an address for the next hop gateway.
To make it easy to pass this reorder inet_prefix so that it's tail
is a proper RTA_VIA attribute.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Add the functions family_name and read_family to convert an address
family to a string and to convernt a string to an address family.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
For some address families (like AF_PACKET) it is helpful to have the
length when prenting the address.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Joining multicast group on ethernet level via "ip maddr" command would
not work if we have an Ethernet switch that does igmp snooping since
the switch would not replicate multicast packets on ports that did not
have IGMP reports for the multicast addresses.
Linux vxlan interfaces created via "ip link add vxlan" have the group option
that enables then to do the required join.
By extending ip address command with option "autojoin" we can get similar
functionality for openvswitch vxlan interfaces as well as other tunneling
mechanisms that need to receive multicast traffic.
example:
ip address add 224.1.1.10/24 dev eth5 autojoin
ip address del 224.1.1.10/24 dev eth5
On ip route print dump, label externally offloaded routes with "external".
Offloaded routes are flagged with RTNH_F_EXTERNAL, a recent additon to
net-next. For example:
$ ip route
default via 192.168.0.2 dev eth0
11.0.0.0/30 dev swp1 proto kernel scope link src 11.0.0.2 external
11.0.0.4/30 via 11.0.0.1 dev swp1 proto zebra metric 20 external
11.0.0.8/30 dev swp2 proto kernel scope link src 11.0.0.10 external
11.0.0.12/30 via 11.0.0.9 dev swp2 proto zebra metric 20 external
12.0.0.2 proto zebra metric 30 external
nexthop via 11.0.0.1 dev swp1 weight 1
nexthop via 11.0.0.9 dev swp2 weight 1
12.0.0.3 via 11.0.0.1 dev swp1 proto zebra metric 20 external
12.0.0.4 via 11.0.0.9 dev swp2 proto zebra metric 20 external
192.168.0.0/24 dev eth0 proto kernel scope link src 192.168.0.15
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Reviewed-by: Jiri Pirko <jiri@resnulli.us>
Don't insert newline in -o (oneline) mode; print mark as hex.
Oneline mode is supposed to force all output to be on oneline and
machine-parsable, but this isn't the case for "ip xfrm" as shown:
% ip -o xfrm monitor
...
src 0.0.0.0/0 dst 0.0.0.0/0 \ dir out priority 2051 ptype main \ mark -1879048191/0xffffffff
tmpl src 203.0.130.10 dst 198.51.130.30\ proto esp reqid 16384 mode tunnel\
...
as that's 2 lines, not one. Also, the "mark" is shown in signed
decimal, but the mask is in hex. This is confusing: let's use
hex for both.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
This patch replaces exits with returns in several
iproute2 commands. This fixes `ip -batch -force`
to not exit but continue on errors.
$cat c.txt
route del 1.2.3.0/24 dev eth0
route del 1.2.4.0/24 dev eth0
route del 1.2.5.0/24 dev eth0
route add 1.2.3.0/24 dev eth0
$ip -force -batch c.txt
RTNETLINK answers: No such process
Command failed c.txt:2
RTNETLINK answers: No such process
Command failed c.txt:3
Reported-by: Sven-Haegar Koch <haegar@sdinet.de>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Where used in the ip tool, the 'show' option always has the synonyms
'list' and 'lst', except for ip-token and ip-addrlabel, which are missing
'lst'. Add this as a synonym for these commands.
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Observed on the Linux 3.18:
# ip netns
RTNETLINK answers: Operation not supported
net0
CC: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Fixes: d182ee1307 ("ipnetns: allow to get and set netns ids")
Signed-off-by: Vadim Kochan <vadim4j@gmail.com>
This new attribute is now advertised by the kernel for x-netns interfaces.
It's also possible to set it when an interface is created (and thus creating a
x-netns interface with one single message).
Example:
$ ip netns add foo
$ ip netns add bar
$ ip -n foo netns set bar 15
$ ip -n foo link add ipip1 link-netnsid 15 type ipip remote 10.16.0.121 local 10.16.0.249
$ ip -n foo link ls ipip1
3: ipip1@NONE: <POINTOPOINT,NOARP> mtu 1480 qdisc noop state DOWN mode DEFAULT group default
link/ipip 10.16.0.249 peer 10.16.0.121 link-netnsid 15
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
The kernel now provides ids for peer netns. This patch implements a new command
'set' to assign an id.
When netns are listed, if an id is assigned, it is now displayed.
Example:
$ ip netns add foo
$ ip netns set foo 1
$ ip netns
foo (id: 1)
init_net
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
This patch adds support to remote checksum checksum offload
confinguration for IPIP, SIT, and GRE tunnels. This patch
adds a [no]encap-remcsum to ip link command which applicable
when configured tunnels that use GUE.
http://tools.ietf.org/html/draft-herbert-remotecsumoffload-00
Example:
ip link add name tun1 type gre remote 192.168.1.1 local 192.168.1.2 \
ttl 225 encap fou encap-sport auto encap-dport 7777 encap-csum \
encap-remcsum
This would create an GRE tunnel in GUE encapsulation where the source
port is automatically selected (based on hash of inner packet),
checksums in the encapsulating UDP header are enabled (needed.for
remote checksum offload), and remote checksum ffload is configured to
be used on the tunnel (affects TX side).
Signed-off-by: Tom Herbert <therbert@google.com>
This patch makes CAN_CTRLMODE_FD_NON_ISO netlink feature configurable.
During the CAN FD standardization process within the ISO it turned out that
the failure detection capability has to be improved.
The CAN in Automation organization (CiA) defined the already implemented CAN
FD controllers as 'non-ISO' and the upcoming improved CAN FD controllers as
'ISO' compliant. See at http://www.can-cia.com/index.php?id=1937
Starting with the - currently non-ISO - driver for M_CAN v3.0.1 introduced in
Linux 3.18 this bit needs to be propagated to userspace. In future drivers this
bit will become configurable depending on the CAN FD controllers capabilities.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
"ip addr show up" would exclude the interface (link), but include the
addresses of down interfaces (which looked like they where indented
under a different interface). This fixes the filtering.
For a full example see the original bug report at:
http://bugs.debian.org/776040
Reported-by: Paul Slootman <paul@debian.org>
CC: 776040@bugs.debian.org
Signed-off-by: Andreas Henriksson <andreas@fatal.se>
This change allows to exec some cmd on each
named netns (except default) by specifying '-all' option:
# ip -all netns exec ip link
Each command executes synchronously.
Exit status is not considered, so there might be a case
that some CMD can fail on some netns but success on the other.
EXAMPLES:
1) Show link info on all netns:
$ ip -all netns exec ip link
netns: test_net
1: lo: <LOOPBACK> mtu 65536 qdisc noop state DOWN mode DEFAULT group default
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
4: tap0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast state DOWN mode DEFAULT group default qlen 500
link/ether 1a:19:6f:25:eb:85 brd ff:ff:ff:ff:ff:ff
netns: home0
1: lo: <LOOPBACK> mtu 65536 qdisc noop state DOWN mode DEFAULT group default
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
4: tap0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast state DOWN mode DEFAULT group default qlen 500
link/ether ea:1a:59:40:d3:29 brd ff:ff:ff:ff:ff:ff
netns: lan0
1: lo: <LOOPBACK> mtu 65536 qdisc noop state DOWN mode DEFAULT group default
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
4: tap0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast state DOWN mode DEFAULT group default qlen 500
link/ether ce:49:d5:46:81:ea brd ff:ff:ff:ff:ff:ff
2) Set UP tap0 device for the all netns:
$ ip -all netns exec ip link set dev tap0 up
netns: test_net
netns: home0
netns: lan0
Signed-off-by: Vadim Kochan <vadim4j@gmail.com>
This patch adds configuration and dumping of congestion control metric
for ip route, for example:
ip route add <dst> dev foo congctl [lock] dctcp
Reference: http://thread.gmane.org/gmane.linux.network/344733
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
The issue was caused that ifla_vf_rate does not exist on
older kernels and should be checked if it exists as nested attr.
Signed-off-by: Vadim Kochan <vadim4j@gmail.com>
Reported-by: William Dauchy <william@gandi.net>
Tested-by: William Dauchy <william@gandi.net>
Added new '-netns' option to simplify executing following cmd:
ip netns exec NETNS ip OPTIONS COMMAND OBJECT
to
ip -n[etns] NETNS OPTIONS COMMAND OBJECT
e.g.:
ip -net vnet0 link add br0 type bridge
ip -n vnet0 link
Signed-off-by: Vadim Kochan <vadim4j@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
New netns_switch func moved to the lib/namespace.c from ip/ipnetns.c
so it can be used from the other tools for fast switching
network namespace.
Signed-off-by: Vadim Kochan <vadim4j@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Added new option 'type' to 'ip link show'
command which allows to filter devices by type:
ip link show type bridge
ip link show type vlan
Signed-off-by: Vadim Kochan <vadim4j@gmail.com>
Sometimes it's needed to have "ip address show" list only addresses
with certain flags not being set, e.g. in network scripts.
As an example one might want to exclude addresses in "tentative"
or "deprecated" state.
Support listing addresses with flags tentative, deprecated, dadfailed
not being set by prefixing the respective flag with a minus.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Added another timestamp format to look like more logging info:
[2014-12-22T22:36:50.489 ] 2: enp0s25: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default
link/ether 3c:97:0e:a3:86:2e brd ff:ff:ff:ff:ff:ff
Signed-off-by: Vadim Kochan <vadim4j@gmail.com>
This patch makes CAN_CTRLMODE_PRESUME_ACK netlink feature configurable.
When enabled, the feature sets CAN controller in mode in which
acknowledgement absence is ignored.
Signed-off-by: Nikita Edward Baruzdin <nebaruzdin@gmail.com>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Stephen Hemminger
Vadim Kochan
Lubomir Rintel
Eric W. Biederman
Madhu Challa
Scott Feldman
philipp@redfish-solutions.com
Roopa Prabhu
Mark Einon
Nicolas Dichtel
Tom Herbert
Oliver Hartkopp
Thomas Graf
Andreas Henriksson
Daniel Borkmann
Jiri Pirko
Duan Jiong
Heiner Kallweit
Nikita Edward Baruzdin