Observed on the Linux 3.18:
# ip netns
RTNETLINK answers: Operation not supported
net0
CC: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Fixes: d182ee1307 ("ipnetns: allow to get and set netns ids")
Signed-off-by: Vadim Kochan <vadim4j@gmail.com>
This new attribute is now advertised by the kernel for x-netns interfaces.
It's also possible to set it when an interface is created (and thus creating a
x-netns interface with one single message).
Example:
$ ip netns add foo
$ ip netns add bar
$ ip -n foo netns set bar 15
$ ip -n foo link add ipip1 link-netnsid 15 type ipip remote 10.16.0.121 local 10.16.0.249
$ ip -n foo link ls ipip1
3: ipip1@NONE: <POINTOPOINT,NOARP> mtu 1480 qdisc noop state DOWN mode DEFAULT group default
link/ipip 10.16.0.249 peer 10.16.0.121 link-netnsid 15
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
The kernel now provides ids for peer netns. This patch implements a new command
'set' to assign an id.
When netns are listed, if an id is assigned, it is now displayed.
Example:
$ ip netns add foo
$ ip netns set foo 1
$ ip netns
foo (id: 1)
init_net
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
This patch adds support to remote checksum checksum offload
confinguration for IPIP, SIT, and GRE tunnels. This patch
adds a [no]encap-remcsum to ip link command which applicable
when configured tunnels that use GUE.
http://tools.ietf.org/html/draft-herbert-remotecsumoffload-00
Example:
ip link add name tun1 type gre remote 192.168.1.1 local 192.168.1.2 \
ttl 225 encap fou encap-sport auto encap-dport 7777 encap-csum \
encap-remcsum
This would create an GRE tunnel in GUE encapsulation where the source
port is automatically selected (based on hash of inner packet),
checksums in the encapsulating UDP header are enabled (needed.for
remote checksum offload), and remote checksum ffload is configured to
be used on the tunnel (affects TX side).
Signed-off-by: Tom Herbert <therbert@google.com>
This patch makes CAN_CTRLMODE_FD_NON_ISO netlink feature configurable.
During the CAN FD standardization process within the ISO it turned out that
the failure detection capability has to be improved.
The CAN in Automation organization (CiA) defined the already implemented CAN
FD controllers as 'non-ISO' and the upcoming improved CAN FD controllers as
'ISO' compliant. See at http://www.can-cia.com/index.php?id=1937
Starting with the - currently non-ISO - driver for M_CAN v3.0.1 introduced in
Linux 3.18 this bit needs to be propagated to userspace. In future drivers this
bit will become configurable depending on the CAN FD controllers capabilities.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
"ip addr show up" would exclude the interface (link), but include the
addresses of down interfaces (which looked like they where indented
under a different interface). This fixes the filtering.
For a full example see the original bug report at:
http://bugs.debian.org/776040
Reported-by: Paul Slootman <paul@debian.org>
CC: 776040@bugs.debian.org
Signed-off-by: Andreas Henriksson <andreas@fatal.se>
This change allows to exec some cmd on each
named netns (except default) by specifying '-all' option:
# ip -all netns exec ip link
Each command executes synchronously.
Exit status is not considered, so there might be a case
that some CMD can fail on some netns but success on the other.
EXAMPLES:
1) Show link info on all netns:
$ ip -all netns exec ip link
netns: test_net
1: lo: <LOOPBACK> mtu 65536 qdisc noop state DOWN mode DEFAULT group default
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
4: tap0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast state DOWN mode DEFAULT group default qlen 500
link/ether 1a:19:6f:25:eb:85 brd ff:ff:ff:ff:ff:ff
netns: home0
1: lo: <LOOPBACK> mtu 65536 qdisc noop state DOWN mode DEFAULT group default
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
4: tap0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast state DOWN mode DEFAULT group default qlen 500
link/ether ea:1a:59:40:d3:29 brd ff:ff:ff:ff:ff:ff
netns: lan0
1: lo: <LOOPBACK> mtu 65536 qdisc noop state DOWN mode DEFAULT group default
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
4: tap0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast state DOWN mode DEFAULT group default qlen 500
link/ether ce:49:d5:46:81:ea brd ff:ff:ff:ff:ff:ff
2) Set UP tap0 device for the all netns:
$ ip -all netns exec ip link set dev tap0 up
netns: test_net
netns: home0
netns: lan0
Signed-off-by: Vadim Kochan <vadim4j@gmail.com>
This patch adds configuration and dumping of congestion control metric
for ip route, for example:
ip route add <dst> dev foo congctl [lock] dctcp
Reference: http://thread.gmane.org/gmane.linux.network/344733
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
The issue was caused that ifla_vf_rate does not exist on
older kernels and should be checked if it exists as nested attr.
Signed-off-by: Vadim Kochan <vadim4j@gmail.com>
Reported-by: William Dauchy <william@gandi.net>
Tested-by: William Dauchy <william@gandi.net>
Added new '-netns' option to simplify executing following cmd:
ip netns exec NETNS ip OPTIONS COMMAND OBJECT
to
ip -n[etns] NETNS OPTIONS COMMAND OBJECT
e.g.:
ip -net vnet0 link add br0 type bridge
ip -n vnet0 link
Signed-off-by: Vadim Kochan <vadim4j@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
New netns_switch func moved to the lib/namespace.c from ip/ipnetns.c
so it can be used from the other tools for fast switching
network namespace.
Signed-off-by: Vadim Kochan <vadim4j@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Added new option 'type' to 'ip link show'
command which allows to filter devices by type:
ip link show type bridge
ip link show type vlan
Signed-off-by: Vadim Kochan <vadim4j@gmail.com>
Sometimes it's needed to have "ip address show" list only addresses
with certain flags not being set, e.g. in network scripts.
As an example one might want to exclude addresses in "tentative"
or "deprecated" state.
Support listing addresses with flags tentative, deprecated, dadfailed
not being set by prefixing the respective flag with a minus.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Added another timestamp format to look like more logging info:
[2014-12-22T22:36:50.489 ] 2: enp0s25: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default
link/ether 3c:97:0e:a3:86:2e brd ff:ff:ff:ff:ff:ff
Signed-off-by: Vadim Kochan <vadim4j@gmail.com>
This patch makes CAN_CTRLMODE_PRESUME_ACK netlink feature configurable.
When enabled, the feature sets CAN controller in mode in which
acknowledgement absence is ignored.
Signed-off-by: Nikita Edward Baruzdin <nebaruzdin@gmail.com>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
The issue was observed when IPv6 router broadcasted NDUSEROPT
messages which are not handled by monitor and caused printing
'Timestamps' w/o message because such kind of rtnl messages is not
handled by monitor.
As 'ip monitor' by default subscribes to the all mcast rtnl groups except
RTGRP_TC then all messages of these rtnl groups which are not handled by
monitor may cause such issues.
Fixed by subscribing by default to rtnl mcast groups which are
supported by 'ip monitor'.
Signed-off-by: Vadim Kochan <vadim4j@gmail.com>
This option was used only for 'ip link', but it can be useful to have it for
'ip address'. Thus it is possible to display link details and addresses with one
command.
Example:
$ ip -d a ls dev gre1
9: gre1@NONE: <POINTOPOINT,NOARP,UP,LOWER_UP> mtu 1468 qdisc noqueue state UNKNOWN group default
link/gre 10.16.0.249 peer 10.16.0.121 promiscuity 0
gre remote 10.16.0.121 local 10.16.0.249 ttl inherit ikey 0.0.0.10 okey 0.0.0.10 icsum ocsum
inet 192.168.0.249 peer 192.168.0.121/32 scope global gre1
valid_lft forever preferred_lft forever
inet6 fe80::5efe:a10:f9/64 scope link
valid_lft forever preferred_lft forever
Suggested-by: Christophe Gouault <christophe.gouault@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
This option was used only for 'ip link', but it can be useful to have it for
'ip address'. Thus it is possible to display link details and addresses with one
command.
Example:
$ ip -d a ls dev gre1
9: gre1@NONE: <POINTOPOINT,NOARP,UP,LOWER_UP> mtu 1468 qdisc noqueue state UNKNOWN group default
link/gre 10.16.0.249 peer 10.16.0.121 promiscuity 0
gre remote 10.16.0.121 local 10.16.0.249 ttl inherit ikey 0.0.0.10 okey 0.0.0.10 icsum ocsum
inet 192.168.0.249 peer 192.168.0.121/32 scope global gre1
valid_lft forever preferred_lft forever
inet6 fe80::5efe:a10:f9/64 scope link
valid_lft forever preferred_lft forever
Suggested-by: Christophe Gouault <christophe.gouault@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
This permits to selectively enable explicit congestion notification via
the routing table.
If this ecn feature is not set, the kernel will use the tcp_ecn sysctl
to decide wheter to use ECN when establising a TCP connection.
At the time of this writing, the kernel supports ecn and allfrags, but
allfrags is of dubious value and not implemented here.
Example:
ip route change 192.168.2.0/24 dev eth0 features ecn
Signed-off-by: Florian Westphal <fw@strlen.de>
Adding basic support to create virtual devices using 'ip'
utility. Following is the syntax -
ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ]
e.g. ip link add link eth0 ipvl0 type ipvlan mode l3
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Laurent Chavey <chavey@google.com>
Cc: Tim Hockin <thockin@google.com>
Cc: Brandon Philips <brandon.philips@coreos.com>
Cc: Pavel Emelianov <xemul@parallels.com>
As 'ip' util will share the same netns from the caller
process then we can just look at /proc/self/.. to show
the netns of the current process by:
ip netns id
Signed-off-by: Vadim Kochan <vadim4j@gmail.com>
Add udpcsum option to enable transmitting UDP checksums when doing
VXLAN/IPv4. Add udp6zerocsumtx, and udp6zerocsumrx options to enable
sending zero checksums and receiving zero checksums in VXLAN/IPv6.
Signed-off-by: Tom Herbert <therbert@google.com>
This patch adds support to configure foo-over-udp (FOU) and Generic
UDP Encapsulation for GRE tunnels. This configuration allows selection
of FOU or GUE for the tunnel, specification of the source and
destination ports for UDP tunnel, and enabling TX checksum. This
configuration only affects the transmit side of a tunnel.
Example:
ip link add name tun1 type gre remote 192.168.1.1 local 192.168.1.2 \
ttl 225 encap fou encap-sport auto encap-dport 7777 encap-csum
This would create an GRE tunnel in GUE encapsulation where the source
port is automatically selected (based on hash of inner packet) and
checksums in the encapsulating UDP header are enabled.
Signed-off-by: Tom Herbert <therbert@google.com>
This patch adds support to configure foo-over-udp (FOU) and Generic
UDP Encapsulation for IPIP and sit tunnels. This configuration allows
selection of FOU or GUE for the tunnel, specification of the source and
destination ports for UDP tunnel, and enabling TX checksum. This
configuration only affects the transmit side of a tunnel.
Example:
ip link add name tun1 type ipip remote 192.168.1.1 local 192.168.1.2 \
ttl 225 encap gue encap-sport auto encap-dport 9999 encap-csum
This would create an IPIP tunnel in GUE encapsulation where the source
port is automatically selected (based on hash of inner packet) and
checksums in the encapsulating UDP header are enabled.
Signed-off-by: Tom Herbert <therbert@google.com>
Added 'ip fou...' commands to enable/disable UDP ports for doing
foo-over-udp and Generic UDP Encapsulation variant. Arguments are port
number to bind to and IP protocol to map to port (for direct FOU).
Examples:
ip fou add port 7777 gue
ip fou add port 8888 ipproto 4
The first command creates a GUE port, the second creates a direct FOU
port for IPIP (receive payload is a assumed to be an IPv4 packet).
Signed-off-by: Tom Herbert <therbert@google.com>
Vadim Kochan
Nicolas Dichtel
Stephen Hemminger
Tom Herbert
Oliver Hartkopp
Thomas Graf
Andreas Henriksson
Daniel Borkmann
Jiri Pirko
Duan Jiong
Heiner Kallweit
Nikita Edward Baruzdin
Florian Westphal
Mahesh Bandewar
Pavel Simerda